Wind power in Germany is leading the way in the field of renewable electricity generation. The installed capacity of all wind turbine generators (WTG’s) in the country amounted of more than 60,000 megawatts (MW) at the end of 2019 and the WTG’s installed by 50Hertz contributed to approximately one third of this capacity (onshore as well as offshore).
Within the 50Hertz grid area, approximately 36 per cent of all wind turbines installed in Germany feed into the medium and high-voltage grids of the regional distribution system as well as into the extra high-voltage grid of 50Hertz.
Installed capacity onshore (figures from 2018):18.711MW
Installed capacity offshore (figures from 2018):1.068MW
Wind turbines are the most important form of renewable energy exploitation,generating electricity both on land (onshore) and in the open sea (offshore). Very simply put, they work as wind mills combined with a dynamo: the wind makes the rotor turn and this movement is transformed into electrical energy by a generator.The first wind turbines were already used for electricity generation in the early 20th century. Nevertheless, the worldwide interest in electricity generation by means of wind turbines only began to increase significantly after the oil crises of the 1970s. The development of the large renewable installations that are now common, began in the 1990s and has shown a strongly rising trend that continues to this day. This is due to requirements coming into force within the German Renewable Energy Sources Act (EEG) in the year 2000.
Unlike conventional power plants or renewable biomass installations, the electricity generation from wind energy fluctuates and strongly depending on the weather conditions. Unfortunately, the generational capacity from wind turbines rarely matches the electricity demand at the time. Depending on the wind speed, the volume of electricity generated by wind turbines varies and due to requiring large open spaces for efficient generation, turbines are often found in sparsely populated areas with a correspondingly low electricity demand.
The operators of the German energy supply grids are obliged by the EEG to feed in all electricity generated from renewable sources into the grid with a high priority. In order to maintain the balance between offer and demand, 50Hertz (as transmission system operator, TSO) has to compensate for the fluctuations in generational capacity which, at times, can be considerable.As the TSO is responsible for the grid area in the eastern German states and Hamburg, 50Hertz ensures the permanent balance between the electricity offered and demanded - and therefore maintains a constant grid frequency, which is a decisive factor for supply security.
Below, you will find a summary relating to wind power in the 50Hertz grid area.
Grid area of 50Hertz Transmission: wind power specifications 2014 to 2017
The data from the table refer to wind power generational capacity, including direct marketing, and are based on the extrapolation of the actual figures (15 minute mean capacity figures).
The following forecasted and extrapolated data show the wind power being fed into the 50Hertz grid area.
These data are of particular interest for market players such as wind power electricity traders and direct marketers, but also for associations, politics or universities, which is why 50Hertz makes them publically available.
The forecast values for wind power feed-in to the 50Hertz grid area are based on values from service providers. The data provided is always those of 09:00 hrs the previous dayand the publication takes place daily at 18:00 hrs for the entire following 24 hours.
Based on the weather models (e.g. GFS, ECMWF) and the master data (geographic coordinates, address etc.) of the individual PV installations, physical as well as statistical capacities are calculated for the near future of up to eight days.
For each 15 minute duration, a capacity value is supplied in megawatts (MW). A quarter of an hour for which no values are given, is entered as ‘not available’ (n.a.).
A table of the wind power feed-in values, including past values, is available here for download in CSV Format:
The actual (onshore & offshore) wind power feed-in values in the 50Hertz grid area presented in the chart are determined by extrapolation of the current measured values from selected wind farms.
The 15 minute mean from the extrapolation is published as the capacity value in megawatts (MW) for the relevant quarter of an hour. A quarter of an hour for which no values are given, is entered as ‘not available’ (n.a.) up to and including 2008, and is given -1 as value as of 2009.
A table, including past values, is available here for download in CSV Format:
Here you can find our publications on wind power feed-in of the previous years: